- What is 10 2 Romex used for?
- What size wire is good for 100 amps?
- Can 10 gauge wire handle 60 amps?
- What size wire do you need for a 50 amp breaker?
- Can I use 10 2 wire for a stove?
- How many amps can 10 3 wire carry?
- How far can you run 10 3 wire?
- What’s the difference between 10 2 wire and 10 3 wire?
- Is 10 3 wire heavy enough for a dryer?
- Can you use 8 2 dryer wire?
- How many amps can 6 3 wire carry?
- What size wire do I need to hook up a dryer?
- Can you use 12 3 wire for a dryer?
- Will 10 gauge wire carry 50 amps?
- How far can 12 2 wire run?
What is 10 2 Romex used for?
Romex is used for most lighting and outlet circuits in your home.
Romex will be labeled with “12-2” or “12-3”.
The first number indicates the gauge of the wire….The following NEC regulations apply to Romex conductors:Wire Gauge or TypeRated AmperageCommon Uses10-2 Romex30 AElectric water heater, baseboard heaters7 more rows.
What size wire is good for 100 amps?
When it comes to the lines connecting master and secondary panels, where the line will carry as much as a full 100 amps, use a 2-gauge non-metallic sheathed electrical cable. The cable must contain one or two hot wires depending on your needs, one neutral wire, and one ground wire. Each wire should be 2-gauge in size.
Can 10 gauge wire handle 60 amps?
Old(s) Fart. Not only is #10 wire on a 60 amp breaker a bad idea, it is completely against code. Also, the 60 amp breaker is completely unnecessary. A 30 amp breaker (which IS correct for #10 wire) is adequate for this compressor.
What size wire do you need for a 50 amp breaker?
For a maximum of 50 amps, you’ll need a wire gauge of 6. Fifty amp breakers are most often used to power many different appliances.
Can I use 10 2 wire for a stove?
The Ground wire on 10-2 should not be used for neutral. The appliance most likely uses 120V as well as 240V. Good Luck on your project.
How many amps can 10 3 wire carry?
30 ampsWhat Type & Gauge of Wire Should I Use?Type NM-B (Typical Indoor Applications)*12/3 with ground3-way Light Switches10/3 with groundApartment size Range – up to 30 amps Built-in Single Ovens – up to 30 amps10/2 with groundElectric Wall Heater – up to 30 amps8/3 with groundDouble Oven Range – up to 45 amps3 more rows
How far can you run 10 3 wire?
10/3 will be fine for 50′. That’s about as long as you’d wanna go, though. a good rule of thumb is that voltage drop doesn’t start becoming an issue until the distance in feet is greater than the number of the voltage level (e.g. 120 ft for 120 volt, 240 ft for 240 volt, etc.)
What’s the difference between 10 2 wire and 10 3 wire?
For your welder what you want is 10-2 with a ground. The 10-3 is mainly used for household ranges that have 4 prongs on the plug it also has a ground wire.
Is 10 3 wire heavy enough for a dryer?
3 Answers. 10/3 is FINE for the dryer. 12/2 for the washer. Typically a 220v/30 amp Dryer circuit would utilize 10/3 with ground.
Can you use 8 2 dryer wire?
No, you cannot use it for your generator, unless you only want to pull 120 volts from it. Why are you using 8 gage wire for an electric dryer? 10 gage is sufficient.
How many amps can 6 3 wire carry?
6/3 is normally protected with a 60-amp breaker. Since there are no 55-amp breakers, code allows you to round up to the next larger standard size.
What size wire do I need to hook up a dryer?
The typical cable used for a dryer circuit is 10/3 Type NM cable which has three insulated wires and a bare ground wire, totaling four wires in all. The typical 220 or 240volt electric heat dryer requires a dedicated circuit, which means that the circuit is not shared with any other device.
Can you use 12 3 wire for a dryer?
If it’s an electric dryer it needs 30A@240v. It should be wired with 10/3 w/gr on a 2P30Amp breaker. #12 wire is only rated for 20Amps max.
Will 10 gauge wire carry 50 amps?
10 AWG coper wire is rated for 30 Amps in most installations. 50 Amps calls for 6 AWG or 8 AWG high temperature cable.
How far can 12 2 wire run?
The total circuit would be about 60 -70 feet in length. It would only be supplying about 5 outlets and one light. It would be a light load, running small things, no heaters or med/large equipment. #12 provides reasonable performance up to about 100′ with general loads like you describe.